Call Today · 9am–10pm

Black double swing gate on an automated driveway entrance, illuminated brick piers at dusk

Solutions

Keep automated gates running safely — planned or reactive.

An automated gate is powered machinery. Planned maintenance catches wear before it becomes a breakdown; reactive repair covers it when something's already gone wrong.

Planned maintenance

Scheduled visits check the items most likely to wear or drift out of calibration, reducing the likelihood of an unplanned breakdown.

  • Safety devices tested (photocells, safety edges, force limiting)
  • Hinges, tracks, rollers and fixings inspected for wear
  • Manual release and battery backup tested
  • Control system and access credentials checked

Reactive repair

Covers automated gates and access systems that have stopped working correctly — including installations not originally carried out by us. Signs it’s time to book a visit: slower or jerky movement, unusual noise, a gate that won’t fully close, or an unreliable intercom or keypad.

Request a repair visit
Beninca

Systems We Work On

Servicing and repair covers automated gates running control systems from established gate-automation manufacturers — including systems we didn’t originally install.

Planned Maintenance

What a gate service covers, and how often it should happen.

An automatic gate is a moving machine used every day in all weathers. A service keeps it safe as well as working — the safety devices are what wear out of adjustment first, and they are the part nobody notices until it matters.

How often

Most residential gates are serviced every six months to a year, depending on use and exposure. Busy commercial and shared entrances usually need more frequent visits, because wear tracks the number of cycles rather than the calendar.

Safety testing

Photocells are aligned and tested, safety edges are checked for damage and correct response, and the operator's force is measured and adjusted so the gate stops and reverses on contact as it should.

Mechanical wear

Hinges, bearings, rollers, racks and gate stops are inspected, cleaned and lubricated. On sliding gates the track and run-back area are cleared; on underground operators the foundation box drainage is checked for standing water.

Power, batteries and release

Backup batteries lose capacity with age. They are tested under load, the manual release is operated, and the control panel is checked for moisture, insect ingress and loose connections.

Access devices

Remotes, keypads, fob readers, intercoms and ANPR cameras are tested end to end, and lost or old credentials can be removed from the system during the visit.

Access control options

A written record

A service should leave a written record of what was checked, what was adjusted and what is likely to need attention next. For landlords, managing agents and businesses, that record is part of showing the gate is being maintained.

Repairs

Common faults, and what usually causes them.

Gate opens but will not close

Most often a photocell that is dirty, knocked out of line or obstructed — the gate is doing exactly what its safety system tells it to. Occasionally it is a failed photocell or a wiring fault after groundwork.

Slow, jerky or noisy movement

Usually a mechanical problem: dry or worn hinges and rollers, debris in a track, or a leaf that has dropped. Left alone it loads the motor and shortens its life, so it is worth looking at before it fails.

Nothing happens at all

Check the supply and the remote battery first. Beyond that it can be a tripped supply, a flat backup battery, a control board fault or water in an underground motor — all diagnosable on a repair visit.

Power cuts

With battery backup the gate keeps running for a limited number of cycles. Without it, the manual release lets the gate be opened and closed by hand until power returns — your handover pack should show where the release is and how it works.

Systems we did not install

We repair and service automatic gates and access systems from other installers. If an older installation is missing safety devices it should have, we will explain what is needed to bring it up to current practice.

Repair or replace?

A failed operator can often be replaced on its own, keeping the gate. Where the leaf, posts or groundwork are the real problem, that should be fixed first — a new motor on a dropped or binding gate simply wears out again.

Automation for existing gates

Questions

Servicing & repairs — common questions.

Yes. Planned maintenance visits check safety devices, moving parts and control systems, reducing the likelihood of unplanned breakdowns and keeping the installation operating safely.

Our servicing and repairs service covers reactive repair for automated gates and access systems, including those not originally installed by us.

Book a maintenance or repair visit.

Tell us what's happening and we'll advise on next steps before scheduling a visit.